Fish On A Pole Balloon Shape Instructions
by Veronica
Finished Fish On Pole
1. First, blow up a balloon, almost all the way.
2. Make the balloon into a fish shape. Just fold the balloon in half, and twist, leaving just about 2 inches on either side of the tail. Kind of like this: >o
3. Now, you'll need some string. Cut off a piece and tie it to the front of the fish, like where its mouth would be. You can also draw eyes on the fish: >o-----
4. Now, you'll need to make another balloon. This one will be used to make the fishing pole. Blow this one up almost all the way.
5. Make this balloon into a sword.
6. Just tie the string to the small part left on the sword balloon that wasn't blown up to attach the fish, and there you go!
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
Twisting a Balloon into a Swan - On Video
by Robin G.
(Seattle, WA)
Here's a cool video I ran into on YouTube that shows how easy it is to twist a balloon into a swan. I hope this helps!
Click here to read or post comments.
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
Balloon Person
by Sarah
(Vancouver)
Balloon Person
A person made out of lots of balloons!
Click here to read or post comments.
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
Fish On A Fishing Pole Balloon Shape
by Jack Amato
(St. Louis, MO)
Fish On Fishing Pole
First you need to make a sword.
then you take a balloon that has not been blown up yet and you tie that to the end of your sword then make the fish and tie it to the end of the string!!
Click here to read or post comments.
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
How To Make A Balloon Hat Shape
by Anonymous
(Israel)
A simple balloon hat
1. Blow 3 balloons in the colors you want with a two-inch tail.
2. Spin them toghether a few inches from the knot.
3. Put around the head and check the size, save the other closing spot on the head.
4. Spin the balloons toghether 0.5 inches from the spot you saved and if you leave a tail its fine.
5. Take the third balloon and add it on the spin points of the two balloons (this is the hard part)
6.(optional) Use the tail to decorate the hat, in the picture I made it without decorations.
p.s, sorry if i am confusing cause i am a begginer ballon folder
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
Mouse Balloon Shape
by Genny
(Zebulon, NC, USA)
Balloon Mouse
Take a size 260 long balloon, leave 1/2 of the balloon un-inflated (for the long tail of the mouse). Make three 1 and 1/2 inch circles at the top of the balloon. Bend over only two of the circles and twist the two that are beside each other. Make three more 1 and 1/2 inch circles and do the same. Then with the remaining inflated portion of the balloon make four 1 and 1/2 inch Bend two of the four circles over and twist the first two circles. And that's your mouse!
~ genny ~
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
How To Make A Balloon Boat Shape
by Ryan Baker
(Abbotsford, B.C., Canada)
1. Blow the balloon up and leave about a thumb length of space.
2. Then take the balloon fold it to the half point and twist the ends together.
3. Finally go slightly above the center of the balloon and twist there if you want you can make a poodle tail like thing on the top of the antenna.
Now you have a balloon boat enjoy. :)
Click here to read or post comments.
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
Twisting a Balloon into a Monkey
by Deven
(USA)
1. To make a balloon monkey, inflate a 260 all to about 5-6 inches.
2. Then, make a small flower petal no more than 5 inches across.
3. Next, make a pinch twist (ear twist).
4. Now make a bubble just a little bit longer than the pinch twist.
5. Do another pinch twist.
6. Twist the first ear twist you made into the last ear twist you just made (This is a little confusing, but the instructions are on youtube).
7. You just made the head of the monkey! Now, make a small segment, a small bubble, another small bubble, and another small segment. Twist the two small segments together.
8. Do a small segment for the body.
9. Do basic dog legs for the back legs.
10. Now curve up the tail a bit to give your monkey some character!
check it out on youtube:
Click here to read or post comments.
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
Giraffe Balloon Twisting
Go by the same instructions for making the dog balloon (at the top of this page), but just make the giraffe with a longer neck!
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
How To Make A Giraffe Balloon Shape
by Briana
(FL)
Hi, I have been blowing balloons for years. All you have to do is make a dog but make a large space between head and legs (to make a really long neck :)
Join in and write your own page! It's easy to do. How?
Simply click here to return to Balloon Shapes.
